Blog

Smyrna Water Heater Sediment Removal

Posted by on Mar 30, 2015 in Gas Water Heater Repair Smyrna GA, Water Heater Repair Smyrna GA | 0 comments

If you have an issue with sediment, you’re most likely currently familiar with it. Gas fired water heaters in specific typically suggest that there is a sediment issue with rumbling sounds each time the tank cycles, while still preserving great water temperature level. Fortunately, sediment can quickly be eliminated, and help prevent the need for a Smyrna water heater repair.Water Heater Repair Smyrna GA

If you have a gas water heater, turn the control to pilot. If you have an electric design, you must shut off the electrical energy at the panel. Next turned off the water above the heater so no brand-new water can get in the tank. Then connect a hose to the drain valve. The various other end of the hose must ideally go to a floor drain, although a container can likewise be utilized.

Open the drain valve to eliminate all the water from the tank. Many of the sediment must be eliminated by this easy act. Keep the drain valve open, however switch on the water also, enabling some to get in the tank. Turn off the water after a couple of minutes. Repeat this a number of times to coax as much sediment out with the water.

As a last procedure, close the drain and fill the tank a minimum of half full. Then you can drain it for a last time to eliminate any last remains of sediment. To avoid additional typical sediment issues, you can set up a sediment filter for your tank if your issue is mainly with sand. A sand filter must be set up on the cold trunk line.

Often sediment can likewise obstruct up the drain valve itself. Preferably you must have the ability to wash the valve out under high pressure, however often the valve has to be changed after a cleaning. You can achieve this job while the tank is still complete, simply shut off the gas or electrical energy and await the water in the tank to cool. You must likewise not utilize any water in your home will finishing the replacement.

To eliminate the drain valve, just utilize a big groove joint pair of pliers to turn off the old valve. Then set up a replacement valve by turning it in clockwise. Make sure to utilize pipe thread sealing tape or pipe joint substance on the threads to guarantee that the connection will prove out.

If you are preparing to eliminate the drain valve, you might think about prior to setting up the replacement valve providing your tank a last flush. This is finest done if you have a floor drain that will rapidly drain the water and sediment.

The follow video illustrates this process:

Lots of people erroneously think that a sediment filled tank or a leaking drain valve is source to change the whole hot water heater. By these easy upkeep actions, a lot of property owners must have the ability to handle any issues on their own. Obviously, Water Heater Repair Smyrna GA is here to assist with this or any other water maintenance that ought to be carried out for you.

Take a look at a few of our additional related water heater repair and maintenance articles:

Eliminating Water Heater Odors

Preventative Water Heater Maintenance in 10 Minutes

Eliminating Water Heater Odors

Posted by on Mar 11, 2015 in Water Heater Repair Smyrna GA | 0 comments

Are you experiencing issues with stinky odors originating from the water originating from your water heater? It can occur sometimes for a few various reasons. Here is what Water Heater Repair Smyrna GA advises to do to have your water smelling and tasting much better quickly.

Reasons for Smyrna Water Heater Smells?

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more: http://www.soquelcreekwater.org/content/how-get-rid-odor-water

The most usual reason for hot water smell is microorganisms getting into the water supply. This is more common in houses that make use of well water and cities that make use of wells as their water supply.

With a water heater temperature level setting of 140 degrees or higher will assist in minimizing the development of microorganisms inside of the water storage tank.

Ways to Get Rid of Foul Water Odors

The following instructions describe the way to use chlorine bleach to thoroughly clean a water heater.

The electric or gas leading to the water heater tank has to first be turned off.

Next, the cold water supply off that goes to the tank needs to be turned off.

Open the hot water faucet of the kitchen area sink to permit air to get in the tank.

With a a yard hose hooked up to the storage tank drain valve, drain the water inside the water heater.

Then shut the drain valve as soon as it is empty.

The next step is putting in the bleach.
If the hose for the cold water going inside the storage tank is a flexible line, unscrew it from the tank. Otherwise, one will have to take off the pressure relief valve, which is more involved. For electric water heaters, one of the elements can be removed.

Make use of a funnel to get bleach inside the tank.
Add 5 ounces of bleach per gallon of the tank ability.
Case in point – A 50 gallon water heater will require 250 ounces of bleach, that is around 2 gallons.

Reinstall the water line or pressure relief valve.

Fill the tank back up with water once more.

Close up the hot water faucet of the kitchen area faucet as quickly as all the air runs out the line.

Operate all the hot water appliances up until the aroma of bleach is obvious. We want to get rid of the microorganisms that can be found in the water lines likewise, not only inside of the water heater.

Allow the water to stay in the tank and water lines undisturbed for 2 to 3 hours.

Empty the storage tank once more and refill it. This time let it remain undisturbed for thirty minutes and drain it one additional time.

Fill the tank back up. Open all the hot water appliances and let them run up until the scent of bleach is gone.

For gas water heaters, relight the water heater pilot burner. For electric water heaters, turn the electricity on once more.

In addition, by replacing the anode rods, or maybe the type utilized can accomplish the same goal as the next video demonstrates:

More Resources

Controlling Odors in Hot Water Heaters – City of Fellsmere

Solving rotten-egg odor in water heaters

Your Household Water Quality: Odors in Your Water

Repairing a Noisy Smyrna Water Heater

Posted by on Feb 26, 2015 in Water Heater Repair Smyrna GA | 0 comments

Water Heater Repair Smyrna GA is consistently being contacted to have a look at a loud water heater. Popping and knocking noises might be because of a problem with the water heater, but it’s additionally an inconvenience. We are going to examine the most probable reason your water heater may begin generating noise and what you can possibly do to calm it down! Prior to contacting a Smyrna expert, check out one of the most popular water heater troubles and remedies.

The most possible reason a water heater can make noise

Again, if the sound is an clue of issues with the heater that difficulty is most probably sediment build up. The sediment arises from the water in the storage tank. It is typically made of calcium and magnesium debris and is mainly a situation in houses which have hard water.

Whenever the sediment starts to develop at the bottom of the storage tank, it traps a little part of hot water under it. This will cause the hot water to boil as the tank functions. The sounds noticed are the bubbles popping through the sediment.

Moreover, the sediment itself might be the factor for the sounds. The sediment sits at the bottom of the tank and can get burnt up leading to odd sounds. And at times, the sediment can get carried up to the top of the tank and breaks off leading to sounds as it falls back down, striking the sides on its way.

How to avoid a water heater from generating noise

If sediment build-up is what’s triggering the sounds, the heater should be reviewed. Hot Water Heater Repair Smyrna GA can accomplish this and provide the tank a flush or recommend an additional option.

You can also avoid sediment build-up by having expert servicing done on the storage tank at minimum annually. This system involves flushing the tank of any sediment.

Yet another terrific approach is to set up a water softener in your Smyrna property. Water softeners take out minerals from the water prior to it entering the water heater, noticeably lowering sediment build up.

To find out more about other likely concerns and options offer Water Heater Repair Smyrna GA a phone call!

Advantages of Utilizing Heat Pump Water Heaters in the Home

Posted by on Feb 4, 2015 in Heat Pump Water Heaters, Water Heater Repair Smyrna GA | 0 comments

Today Water Heater Repair Smyrna GA wishes to examine making use of a heat pump as a different option to an electric water heater. Well known thought has long been that heat pump water heaters are generally not incredibly energy efficient at heating water, however new research is challenging this thought.Water Heater Repair Smyrna GA

As stated by Sarah Widder, of the Department of Energy’s Pacific Northwest National Laboratory, “Heat pump water heaters can use up to 63 percent less energy than traditional electric water heaters. When water heating makes up about 18 percent of U.S. residential energy use, heat pump water heaters offer a real opportunity for energy savings.” (read more…)

The research concludes that the manner that heat pump water heaters are hooked up to the air ducting can help in reducing overall energy consumption of the dwelling, demonstrating that these types of heat pumps could possibly not have as much impact on the total cooling and heating of the household, as has long been believed.

The analysis, that was executed in the summer and winter of 2013, established 2 identical real world test conditions. The principal distinction was with one heat pump not utilizing ducting, and the other utilizing 2 different ducting approaches. The summary ended up being that the test case with the entirely ducted heat pump water heater would lower yearly power usage by 4.2 %.

The investigators also came to the conclusion that even more evaluating needs to be performed to experiment with additional tactics too and to better examine the home cooling aspects of a heat pump.

Heat pumps are crafted to possess high efficiency and be less expensive to operate compared to continuously heating water in a storage tank water heater. Presently, heat pump water heaters are just about 1 % of new water heater product sales in the U. S.. They can be more expensive than standard water heaters to install but through the running expenses will be able to off set that in the long term. Here is what the Department of Energy has to say.  http://energy.gov/energysaver/articles/heat-pump-water-heaters

Where the heat pump can be found in the household has quite a lot regarding the quantity of efficiency one can get from it, reported by greenbuildingadvisor.com.

If you have any thoughts on this technology and want to check out if it may possibly be a decent match for your Smyrna property, contact us! We are always here to give thoughts on our water heater repairs and installations!

Preventative Water Heater Maintenance in 10 Minutes

Posted by on Sep 24, 2014 in Water Heater Repair Smyrna GA | 0 comments

Water heater maintenance in ten minutes? Yep, that is correct. Water Heater Repair Smyrna GA is going to show one how to carry out some water heater preventative maintenance. And, that’s all it will take to complete these 2 essential water heater upkeep tasks; nonetheless, we understand that these will do an outstanding job of assisting with three things:

  • Having a water heater last much longer for it will save on money with running it.
  • Seeing to it ones water heater runs safely is critical for we do not want it to explode in your home.
  • And having it run as energy efficiently as possible also helps one conserve one some cash.

We are now prepared to spend ten minutes once or twice a year to assist in saving some cash on energy costs.

Testing the T&P Relief Valve
The T&P Valve, also referred to as the temperature and pressure relief valve, has a crucial task. It’s job is to help make sure excess pressure inside the water storage tank does not develop, or in even more easy terms, it makes certain that ones water heater does not explode. The T&P valve has a lever or little handle. All one has to do is lift it some and afterwards let go of it back. It should snap back to its closed position quickly. A little water may be heard entering into the drain pipe below the lever that was just raised and maybe heard some pressure being released also. If none of these things have actually taken place throughout the test, the valve will have to be replaced.

Carry out a Mini Water Heater Tank Flush
Naturally, rust and corrosion will take place inside the water storage tank because of the chemical reactions taking place with all the components inside that are required to warm water. We will not get too technical here, but it is simple to help avoid this process by doing a flush or draining of all or a portion of the water in the storage tank.

For simply a small flush, place a container under the drain valve below the tank. Open the drain valve and fill up the container with water. Drain a minimum of a couple of gallons of water in total. Let the water sit in the pail for a few minutes to settle and analyze if there is much that settles to the bottom of the bucket. If there is, if the water heater has actually not been drained for a very long time (or ever), it would be best to do a full flush of the tank to get as much of the sediment out as possible. You will wish to turn the temperature dial down and might wish to let the water cool down for about an hour initially so it is not too hot while draining it. Likewise, it would be much easier to attach a hose to the drain valve and let the water go outside rather of using pails.

If the water looks fairly clean and clear from the tiny test you should be all set. When the water heater has a large amount of sediment inside of it, it can make loud popping noises and it reduces its effectiveness too.

Though water heaters are fairly maintenance free and uncomplicated to run, whenever one feels the tiniest uneasy or are unsure of what to do, it is always best to have give Water Heater Repair Smyrna a call to assist with ones regular water heater maintenance.

Here is an infographic that illustrates these steps, and check out our blog more water heater tips and advice.

Water Heater Repair Smyrna GA

Smyrna Water Heater Safety Precautions

Posted by on Sep 22, 2014 in Plumbing Repair Smyrna GA, Water Heater Repair Smyrna GA | 0 comments

Correctly keeping ones water heater is crucial not so it works to its full capacity and can conserve some energy cash, however for safety issues too. Yes, it can explode – it does not happen too frequently for residents, but clearly this is something that Water Heater Repair Smyrna GA does not wish to have take place to you!

Vents
Venting can be kind of technical but we will go over the essentials here. The vent ought to be the exact same diameter as the draft diverter of the water heater tank. It is supposed to increase and out (for atmospherically vented heaters). Not other directs like up, down, up and out. For direct-vent water heaters, the vent should head out a side wall. As for power-vent heaters, the fan blows the fumes out, so there is some flexibility in the instructions they are vented.

Any roofing or wall that the vent goes through need to be a double wall. The single wall pass throughs ought to be screwed with 3 screws per section. If these basics are not stuck to, the vents can fall apart with time and carbon monoxide can cause significant troubles within ones house. Naturally we do not desire that to happen!

The only other issue with ventilation is that of backdrafting. The fumes can eat the vents with acid condensation. If plenty of this gets on cold piping and the water heater it will not be a good circumstance for a correctly working water heater. If the fumes return inside the rather of being properly vented outside, the fumes can enter the living locations of the house. Soot troubles can develop as well.

Dielectric Connectors
The steel water heater is linked to cooper pipes by the dielectric connectors. When two these two metals are put together in water electrolysis occurs. The process wears away one metal away to safeguard the other. This procedure is crucial in safeguarding the inside of the water heater. Evaluation for leaks ought to be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of an essential part of the water heater, for it helps ensure the darn thing does not explode under pressure if the temperature level goes beyond the appropriate limitations the water heater is developed for. Once a year (a minimum of) the T&P valve must be examined to ensure, it is working appropriately, for they can be prone to failure. Simply lifting up on the handle water should stream easily out and stop when the handle is released. If it simply runs or trickles, or does absolutely nothing at all, it will should be changed.

The drain lines for the T&P line should not be routed up, because water doesn’t stream uphill too well. Make certain it goes downhill and or out please. If water is running out the drain line frequently, it is the sign of something incorrect too. It might be one of numerous different things that we will not enter into right here – simply speak to a neighborhood plumber please.

Earthquake Straps
Yep, even if you do not live in an earthquake area and are needed to have these on ones water heater, it is an excellent idea to do so. It looks like many all new homes in sub-divisions nowadays have the water heater in the garage. Yes, there is normally a concrete curb in front of it so one does not drive a vehicle into it, however things can unintentionally knock it over so be safe and strap that thank in.

Temperature Level Setting
It seems most residential water heater tanks have settings of warm – hot – really hot … and not degree settings. Some “pointers” on saving energy in your home particularly in the winter season time, say to reduce the setting on the tank to 120 degrees. That’s significant for saving energy but legionella germs, which causes Legionnaire’s illness can expand at 120 degrees. By breathing in the mist from the water in the shower, one can breathe in the bacteria. Try to discover a medium between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature level so beware.

Anode Rods
These generally are made from aluminum and there is absolutely nothing wrong with that in theory, though we recommend utilizing magnesium ones. Let’s say for whatever reason there is some sort of emergency or disaster where one lives and one needed to use the water in the water heater for drinking water (due to the fact that lots of emergency preparedness people encourage doing this). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be packed with aluminum compounds, which is bad for the body. It is bad for the stomach, intestines and joints.

The anodes aid with rust defense and are important in prolonging the life of the water heater. They can also aid with smell problems with the water. Overall, magnesium anodes simply work much better for lots of various reasons like the health perks, let develop of sediment, a quieter water heater, and they often work better with softened water.

Drain Valve
Ok, simply check it a minimum of once a year to make certain the darn thing opens and works. And it is excellent to drain and flush the tank at least once a year anyway (something you obviously are doing already). If for some reason one should utilize the water throughout a catastrophe or drain it to quite a loud tank and have actually not drained it routinely, and it doesn’t open, it will take longer to fix the trouble you are initially attempting to repair.

Combustion Changer Hatch
Considering that gas and oil water heaters breathe the air drawn in from underneath, combust with it and exhale it, it is very important to keep the area around it, specifically underneath the water heater, clean and swept. If if is not burning correctly, it can trigger composing problems (pointed out above), along with combustion and fume troubles and potentially be a fire danger. A few of analyzing the chamber and exactly how the flame burns is objective so we are not going to enter into a lot of detail here. it is necessary to see if the combustion chamber roof has a bunch of rust or water markings or is black in color. These are not a great indicator at all. One must see some blue flame at the bottom when it burns and orange and yellow at the top, nonetheless, the yellow must not be super high up. One should see gray metal, some white condensation marks are ok.

Here is an infographic to highlight the information above:

Water Heater Repair Smyrna GA

Ways to Increase Water Heater Energy Efficiency

Posted by on Jun 13, 2014 in Water Heater Repair Smyrna GA | 0 comments

Few of our consumers at Water Heater Repair Smyrna GA do not wish to be as energy reliable as possible with all of their house costs, including their water heating expense. So, we decided to assemble a list of things that will help property owners do simply that.Water Heater Repair Smyrna GA

energysavers.gov estimates that 14-25 percent of a house’s energy use is from heating water, and it likewise consists of some of the electric costs too. The following pointers will make optimize ones water heater’s efficiency.

  • Relying on the amount and frequency of the need for hot water, a tankless water heater could be a good financial investment come time to have a water heater replacement. They are more costly than standard storage tank water heaters, but over the lifetime of the unit can be more cost effective. Not to mention the prospective energy cost savings of running the tankless water heater.
  • If the temperature of the heater is set above 120 degrees, decreasing it can conserve some energy usage too.
  • If one is lucky enough to be building a new house or doing a remodel, attempt to position the water heater as close the area of the house that will make use of the most hot water. Water heat lost while flowing through the water pipes will certainly be lessened.
  • A solar water heater could be an excellent investment too, and not as dependent on the location of the nation one resides in as lots of people would think. Heck, one can even make one with the quantity of information online, however as plumbing professionals ourselves, we would love to help.
  • Insulate, insulate and insulate some more. All uncovered pipes, not just the hot water ones, must be wrapped with insulation. One can consider utilizing a water heater jacket or blanket in the winter season to help keep the heat inside the storage tank. New tank water heaters are made well with a good insulation value, however every bit will help.
  • This might be hard to do (at least I understand it would be in my home with numerous females) however take much shorter showers.
  • When changing a water heater, make certain it is the correct size for the amount of water that will be used on average. Many times we have seen that property owners have too big of a water heater, which increases the amount of energy required to heat the water … and water that will certainly not be utilized.

Smyrna  water heaters are fairly maintenance free however a yearly evaluation and some small upkeep will certainly help extend its life span and save money with it performing at optimal efficiency. Give us a call to schedule a yearly check.

 

Smyrna Water Heater Carbon Monoxide Poising Prevention

Posted by on Jun 5, 2014 in Water Heater Repair Smyrna GA, Water Heater Safety | 0 comments

We have just recently seen a few news reports about carbon monoxide gas poising being connected back to a water heater as the source and so felt it important to share some about that potential today. Yes, any nonrenewable fuel source burning home appliance creates this fatal gas. Including hot water heaters. Nevertheless, with the correct installation of the water heater, together with routine maintenance, and a working carbon monoxide detector in the house, one can sleep safely.Water Heater Repair Smyrna GA

Reasons for Carbon Monoxide Poisoning

Carbon monoxide (CO) is a colorless, odor free gas that is a bi-product of the burning of a fossil fuel like wood, gasoline, coal, natural gas, or kerosene. Breathing in carbon monoxide gas fumes not only avoids oxygen from being used appropriately by the body, but likewise causes damage to the central nervous system. Persons with existing health issues such as heart and lung disease are especially vulnerable, as are babies, youngsters, pregnant women, and the elderly.

Sources of Carbon Monoxide

The cold weather heating season is when a majority of carbon monoxide gas direct exposures happen due to using unvented supplemental heaters. An unvented supplemental heater is a kind of space heater that utilizes indoor air for heating and vents the gases produced in the heating process out into the house. The majority of heaters of this type use kerosene or natural gas for fuel. While more recent designs have oxygen sensing units that turned off the heater when the oxygen level in the area falls below a certain level, older designs do not have such safety features. Because of these safety problems, unvented space heaters have actually been banned in a number of states. Other sources of carbon monoxide gas are malfunctioning cooking appliances, tobacco smoke, clogged chimneys, auto exhaust, malfunctioning furnaces and gas clothes dryers, wood burning fireplaces, and a hot water heater.

Symptoms of Carbon Monoxide Poisoning

Below are the most common signs of carbon monoxide poisoning however they are not always the exact same for every person who has actually been exposed and many times resemble having food poisoning or the flu. A doctor can help in figuring out for sure.

headache
dizziness
weakness
queasiness and vomiting
rapid heartbeat
seizures
cardiac arrest
loss of hearing
fuzzy vision
disorientation
loss of consciousness or coma
respiratory failure

Defense By Proper Gas Appliance Venting

The CDC offers the following details on preventing CO2 poisoning by making certain ones appliances are vented properly.

  • All gas appliances must be vented so that CO will not build up in your home, cabin, or camper.
  • Never burn anything in a stove or fireplace that isn’t vented.
  • Have your chimney checked or cleaned every year. Chimneys can be blocked by debris. This can cause CO to build up inside your home or cabin.
  • Never patch a vent pipe with tape, gum, or something else. This kind of patch can make CO build up in your home, cabin, or camper.
  • Horizontal vent pipes to fuel appliances should not be perfectly level. Indoor vent pipes should go up slightly as they go toward outdoors. This helps prevent CO or other gases from leaking if the joints or pipes aren’t fitted tightly.  (read more…)

It is certainly crucial to have CO2 detectors in the home. The Colorado State University Extension offers the following pointers when selecting a CO2 alarm.

  • Some inexpensive alarms consist of a card with a spot (spot detectors) that changes color in the presence of CO. The absence of an audible signal does not meet UL or IAS requirements for alarms, so these devices do not provide adequate warning of CO.
  • Some CO alarms have a sensor that must be replaced every year or so. The expense of this part should be a factor in purchase decisions.
  • Battery-operated alarms are portable and will function during a power failure, which is when emergency heating might be used. Batteries must be replaced, although some alarms have long-life batteries that will last up to five years.
  • Line-powered alarms (110 volt) require electrical outlets but do not need batteries. They will not function during a power failure. Some line-powered alarms have battery backups.
  • Some alarms have digital readouts indicating CO levels. Alarms with memories can help document and correct CO problems.  (read more…)

The following video provides some nice security tips for water heaters.

Not to frighten anybody, however we likewise wished to include the following video of a water heater install that is not working correctly and is harmful.

Please see a medical professional promptly if you believe that you or a member of your household may have carbon monoxide gas poisoning. Water Heater Repair Smyrna GA can not stress enough the requirement of ensuring an expert plumbing repair company services and installs any water heater equipment in your house or business.

What is the Perfect Smyrna Water Heater Temperature

Posted by on May 15, 2014 in Water Heater Repair Smyrna GA | 0 comments

There are different views on exactly what is the finest temperature level at which to set ones water heater. Water Heater Repair Smyrna GA will be sharing some of the various views with particular proof from those sources in order for one to make his/her own decision on the subject.

First off, the default setting most water heater manufacturers have their products set at is 140 degrees. If you have actually never inspected this already on your Smyrna Water Heater, that may be what it is set at. Likewise, it can be hard to know for sure exactly what the temperature setting is due to the fact that often times the temperature dial does not have degrees written on it, just warm, hot, really hot … something to that effect. Some people feel they are pre-set at a higher temperature level so it feels remarkable to have a great deal of hot water – type of like trying to create good brand awareness in customers.

In regards to energy cost savings, by turning a water heater down from 140 to 120 degrees, it will conserve in between 6 to 10 percent of total energy used. That equates to between $6 to $20 a year most of the time.

Let’s begin with the most likely the most well known source, the U.S. Department of Energy. They suggest a setting of 120 degrees. The link to their website above provides lots of excellent info on the best ways to minimize ones hot water usage and costs. It is certainly worth a read.

Now for the health threats of too low of a temperature level setting. It can be shown that Legionella bacteria has the optimal growth range between 68 to 122 degrees. It is believed that 25 percent of all water heaters have differing levels of Legionella bacteria contamination.

Legionella bacteria causes a kind of pneumonia and is passed to human beings when one breathes in water contaminated with the bacteria – typically in showers, whirlpool baths and even air conditioning systems. Consuming the water is usually ok. It is an issue with having the germs enter ones lungs.

The Centers for Disease Control and Prevention approximates 8,000 to 18,000 Americans contract the condition yearly. 5 to 30 percent of the cases are deadly.

According to OSHA, “At low levels of contamination, the chance of getting Legionnaires’ disease from a water source is very slight. The problem arises when high concentrations of the organism grow in water systems. Water heaters, cooling towers, and warm, stagnant water can provide ideal conditions for the growth of the organism.”  (read more)

Cases to not have the water heater temperature set at 140 degrees would be if there are kids in your house or possibly with elderly individuals too. The threat of being burnt if the faucet was completely on hot water can be too great. Clearly, anybody living in the house that is at threat of contracting Legionella Disease ought to have it set at 140.

In Conclusion

So decide if there are any concerns of individuals burning themselves if the water temperature is too high. Likewise, be aware of anybody who has concerns of contracting Legionella Disease. Because the yearly cost savings of turning the temperature level down is just about $20 the majority of the time with the typical home’s hot water usage, it could be a great choice to keep the temperature above 120 degrees just for the wellness related advantages; however, Hot Water Heater Repair in Smyrna GA will let you make the call.

Water Heater Repair Smyrna GA

Explore more visuals like this one on the web’s largest information design community – Visually.

Smyrna Water Heater Safety

Posted by on May 9, 2014 in Water Heater Repair Smyrna GA | 0 comments

Water heaters are quite easy on the face of it, and they have actually altered not very much in the past 50 years suggests Water Heater Repair Smyrna GA. Thanks to some essential refinements, they are certainly much better than they used to be, with longer life spans, greater efficiency, and more security features that minimize the threat of injury and property damage.

All water heaters transform energy to heat, and afterwards transfer that heat to water. They are linked to a cold water supply pipe and have at least one pipe for outgoing hot water that directs the heated water to taps and home appliances throughout the house.

Though there is a variety of water heaters in the marketplace, including electric, propane, tankless versions, as well as solar-powered designs, the most usual in the United States is a holding tank fueled by natural gas.

These include a steel tank with a heating element at the bottom and a flue running down the center of the tank to vent the carbon monoxide gas that is a by-product of burning natural gas.

You’ll likewise see some sort of thermostat control on the body of the tank that permits one to turn off the gas and control the pilot light. These thermostats are equipped a temperature-sensing probe that automatically shuts off the gas if it detects that the pilot light goes out or fails to light.

The interior of the tank is bonded with vitreous glass to secure it from rusting. Regardless of this safety sheath, there is still some small amount of steel exposed, caused by limitations in the covering process. That exposed steel is vulnerable to rust. To protect the steel from rusting, the makers install sacrificial anode rods in the tanks, normally made of magnesium or aluminum. Through the procedure of electrolysis, the anode rod corrodes, instead of the tank. The tank will rust if the anode rod is totally eaten, unless one changes it. This is the most usual reason for issues with water heaters.

Preventive Maintenance and Smyrna Water Heater SafetyWater Heater Repair Smyrna GA

For the purposes of this post, we’re willing to presume that water heater was properly set up, and that it passed the house evaluation.

Right here are some of the standard steps to maintaining a water heater in proper shape.

First, eyeball it. Water heaters have lots of rust security inside, however hardly any on the outside, so look out for leakages. Likewise examine for staining, flaking paint, or deterioration on the surface of the tank. External rust can cause your tank to fail just as surely as internal rust. Remember that the exterior shell might look fine on the outside, while consumed with rust on the inside. However, if absolutely nothing appears out of the ordinary, proceed to regular maintenance tasks.

The two principle steps to keeping a water heater are regularly draining the tank to eliminate sediment, and checking the temperature level and pressure release valve (T&P valve) to make sure that it is working effectively.

When a water heater operates, sediment develops. That sediment is in fact calcium carbonate, a mineral present in the water, which is precipitated out through heating. It settles to the bottom of the storage tank, and can shorten the life of a water heater; minimize its effectiveness; obstruct valves, lines and the recirculating pump; and even supply a haven for anaerobic germs. How often one drains the tank depends a lot on the water quality where one lives. Areas that have very hard water require even more regular draining to keep sediment levels low. Usually, the frequency is anywhere from 6 months to 1 year.

The T&P valve is essential for avoiding explosions due to over-pressure, as it instantly releases water at certain crucial pressure levels and prevents the tank from blowing up. Test this valve periodically to ensure that it opens and closes properly, so it will not fail when you require it most.

NOTE: If you have actually never carried out these jobs in the past, it’s a great idea to employ a specialist to do it for you the very first time, and inquire to show you how to do it yourself. While it’s not exceedingly complex, there are potential dangers involved. The risks of doing it improperly are great in contrast to a very little service charge.

Finally, install a carbon monoxide alarm close to your water heater. Carbon monoxide gas is odor-free and colorless, but if your water heater does not vent effectively or starts to back draft, those fatal fumes can enter the residence and endanger the family.

If everything is working correctly, examine the water temperature level with a cooking thermometer to make certain it’s set to your families’ comfort level and to guarantee safety. If the water is too hot, it can heat or trigger injury. Conversely, some people set their water temperature low to attempt to be economical. If the water isn’t hot enough, it can harbor bacteria. A great intermediate setting for your water is above 120 degrees.

Learn more tips on our other blog articles too!

How to Diagnose a Leaking Smyrna Water Heater

Posted by on Apr 11, 2014 in Gas Water Heater Repair Smyrna GA, Water Heater Repair Smyrna GA | 0 comments

Definitely not something that one desires to neglect or postpone, is a leaking water heater. Even if it simply appears to be a little leak, let’s take care of the trouble in a prompt way. Too many times Water Heater Repair Smyrna GA has discovered a minor leak is an indication of a bigger issue at hand, or just about to be at hand.Water Heater Repair Smyrna GA

Aside from the possible trouble the water heater itself might be having, one will wish to make sure the water leaking does not damage the floor or walls in the area of the leakage (not knowing where ones water heater is located). If that little leak ends up being a major leakage, the water damage might be expensive.

Likewise, there are health interested in mold and mildew if the moist locations stay wet for an extended period of time. Some mold spores can be harmful and trigger wellness concerns the EPA alerts.

And, we have yet to see a water heater leak go away or fix itself.

Let’s Figure Out From Where the Leak is Coming
Condensation can form in excessively wet weather, so a little quantity of water under or by the storage tank might not be a leakage. Various other devices or a furnace drain line may be the perpetrator even. Do a great investigation to be sure.

Have a look at the plumbing fittings and the top, sides and bottom of the water heater next. If they seem dry, that is a great sign and once more, could be coming from something else in the room. Not to be extremely evident, but look up directly above the water on the floor and see if an overhead pipe or something else may be the cause.

Here’s a great test to carry out next if all looks alright. Dry the puddle of water. Put some dry paper towels down on top of where the puddle was and examine them occasionally. If they stay dry all is well. If not and there is absolutely nothing else in the location to trigger the water, then it looks like it is the water heater.

When it is know that the heater is leaking, the first thing to do is shut off the power. For electric heaters turn it off at the circuit breaker. For gas heaters, set the dial to off. If the leakage is considerable, certainly turn the supply of water off also.

Even if one is not feeling extremely comfy repairing the leakage oneself, by assisting locate the source of the leakage will at first assist the water heater repair business that will assist.

4 Locations to Check for Leaks on the Water Heater

1. First examine all-time low of the tank. There is a layer of insulation and the tank really has 2 layers to it. An internal leakage will generally be obvious from the bottom of the tank. If the water heater is aging, the in will ultimately rust and wear away and will have to be replaced.

2. The temperature level and pressure relief valve, or called the T&P valve. It can be found on the side of the tank and has actually a pipe linked to it that diminishes the side of the tank to the ground. It’s function is the release additional pressure in the water storage tank. If it is leaking, water may leak out of it by the manage or around where it connected to the tank. Water might be diminishing the pipe it is connected to. One can repair these leaks for the valves can wear. Nonetheless, it is good to be familiar with this for the purpose of the valve is to make sure the tank does not blow up … so it’s type of vital to state the least.

One should a minimum of once a year raise the pressure relief valve to ensure some water will come out and stop once more once the valve is launched. If water still flows or for some reason the valve will not open, it needs replaced.

3. Next check the drain valve. It is simple enough to do. It is found on the side to all-time low of the storage tank. It requires to be closed all the way, certainly. This is a simple repair if it is leaking. Lots of times these are made from plastic and can break. Similar to testing the pressure relief valve yearly, this must be opened and closed to make sure it does not close up from lake of use.

4. Lastly, inspect the tightness of the cold and hot water connections to the water heater, found at the top. They may simply have to be tightened. If after tightening them they still show they are leaking, replacing the connections generally will suffice.

In future posts Water Heater Repair Smyrna GA go into information on exactly how to manage a few of these repairs oneself. Let us know if you do not feel comfy dealing with any of this yourself.

Enhanced by Zemanta

Smyrna Tankless Water Heater Basics

Posted by on Mar 31, 2014 in Tankless Water Heater Repair Smyrna GA | 0 comments

Tankless Water Heater OverviewTankless Water Heater Repair Smyrna

Tankless water heaters hаvе growing in popularity fоr a whilе now. Thеѕе compact units mount оn a wall еithеr inside оr еvеn оutѕidе thе house аnd supply hot water оn demand literally withоut end! Thе Europeans hаvе bееn heating water with tankless heaters fоr years. Mаnу people bеliеvе thаt within thе nеxt 5 tо 10 years 50% оr mоrе оf аll American homes will hаvе a tankless water heater in them! Evеn thе big tank water heater companies hаvе triеd tо jump оn board bу partnering with larger Japanese companies tо hаvе units private labeled fоr them.

Tankless water heaters аrе аvаilаblе in electric, nаturаl gas аnd propane fired models. Thе electric tankless water heaters hаvе advantages оvеr tank type electric models but vеrу fеw рrоvidе еnоugh capacity tо serve multiple fixtures with оnlу оnе unit аnd mау require a larger electrical service tо operate them. Thiѕ hаѕ kерt mоѕt builders frоm uѕing thеm in nеw construction. Althоugh thеу dо tеnd work wеll in small home, condo оr apartment applications whеrе gas iѕ nоt аn option. Fоr thе purpose оf thiѕ tutorial wе аrе gоing tо talk аbоut thе gas fired units. Watch fоr a future article соntаining information оn electric tankless heaters.

Tankless water heaters work оn demand bу uѕing sensors аnd computer boards tо monitor thе flow оf water аnd сhаngе thе rate оf firing tо supply juѕt thе amount оf hot water required fоr thе сurrеnt demand. Alѕо called оn demand heaters, meaning thаt thеу burn lеѕѕ gas tо supply hot water tо ѕоmеthing likе a sink thаn thеу wоuld if уоu аrе uѕing multiple fixtures аt thе ѕаmе time. Thiѕ modulating firing rate аlѕо makes thеm vеrу efficient tо operate аѕ уоu аrе оnlу uѕing thе еxасt amount оf fuel needed аt thаt time.

A term thаt ѕhоuld bе avoided iѕ “instantaneous”. Tankless water heaters аrе nоt instantaneous. It dоеѕ tаkе thеm аbоut 2 seconds tо gо frоm thеir аt rest “off” mode tо producing hot water аt thе ѕеt point temperature. Thiѕ iѕ nоt a big issue however. Thе problem iѕ if a consumer thinks bу hearing thе term “instantaneous” thаt thеу will gеt water аt еvеrу outlet in thе house instantly if thеу gеt a tankless heater, thеу will bе disappointed. Mоѕt homes hаvе mаnу feet оf piping bеtwееn thе water heater аnd thе outlets аnd dо nоt hаvе a recirculating system. Thе amount оf timе it takes frоm whеn a faucet оr оthеr hot water fixture opens tо whеn thе ѕеt point water gеtѕ tо thаt point iѕ called “Lag Time”. In today’s large homes with lоw flow fixtures it iѕ nоt uncommon tо ѕее a lag timе оf оvеr 3 minutes tо gеt hot water tо remote fixtures in a home. Changing thе type оf water heater will nоt improve thе speed оf thе delivery оf water unlеѕѕ thе location оf thе heater iѕ altered оr if a recirculating system iѕ installed. Bесаuѕе оf thеir small size оf course, mаnу timеѕ whеn a tankless heater replaces a tank, it саn bе moved tо a mоrе central location оr nearer tо thе fixtures it iѕ tо serve. Thiѕ mау cut dоwn оn thе lag timе considerably.

Tankless Water heaters save space in a home bесаuѕе thеу tаkе uр NO floor space. Thеу аlѕо dо nоt require protection frоm vehicles if installed in a garage аnd аrе ѕо small thеу саn bе installed in a crawl space оr attic аѕ well. If уоu rеаllу nееd space, mаnу саn bе installed outdoors giving уоu аll оf уоur interior space back. Juѕt bе ѕurе tо choose a model designed fоr outdoor installation аnd with freeze protection fоr уоur area.

Energy Saving Features оf Tankless Water Heaters

Tankless water heater save on fuel bесаuѕе thеу dо nоt hаvе tо maintain a supply оf hot water in a tank аnd аrе typically “always off”. Tank type heaters fire оn аnd оff аll thе timе tо maintain thе temperature оf water in thе tank within аbоut 10 degrees оf thе thermostat setting (called “Stand-by heat loss”). Thiѕ аlѕо саn result in ѕоmе noticeable temperature difference. Tankless water heaters рrоvidе hot water tо thе ѕеt point temperature рluѕ оr minus 2 degrees.

Anоthеr thing thаt makes a tankless hot water heater mоrе fuel-efficient iѕ thаt thеу аrе “fully modulating”. In оthеr words thеу оnlу uѕе thе fuel needed tо heat thе water tо thе ѕеt point аt thе сurrеnt flow rate. If уоu аrе washing уоur hands uѕing undеr 1 gallon реr minute (GPM) уоu will bе аt a lower firing rate thаn уоu wоuld bе if уоu аrе filling уоur tub аt 3 GPM. Thiѕ works muсh likе уоur car. Whеn уоu аrе sitting ѕtill thе car iѕ idling. Whеn уоu wаnt tо gо оr gо faster, уоu givе it mоrе gas аnd whеn уоu gеt whеrе уоu аrе gоing уоu turn it off. With thеir “always off” condition аnd thеir modulating capabilities it iѕ common tо ѕее uр tо a 50% reduction in fuel uѕе whеn changing frоm a tank type heater tо a tankless unit.

If уоu аrе gоing tо сhаngе frоm a 50-gallon gas heater tо a tankless уоu аrе рrоbаblу nоt gоing tо realize ԛuitе thаt muсh energy savings. In fact a 50-gallon tank water heater dоеѕ nоt uѕе muсh mоrе fuel аt аll compared tо mоѕt tankless heaters. Hоwеvеr a 50-gallon tank heater оnlу саn rеаllу givе уоu аbоut 40 gallons оf hot water реr uѕе bеfоrе уоu begin running оut оf hot water. Thе tankless heater will deliver mоrе thаn 300 gallons реr hour fоr mоѕt оf thе year аnd уоu саn nеvеr run out! If it iѕ аn electric tank water thаt уоu аrе replacing, уоur savings mау bе higher thаn 50% depending оn thе size оf thе tank. If уоu rеаllу wаnt tо knоw whаt уоur savings mау be, lооk fоr thе yellow “Energy Guide” sticker оn уоur existing heater аnd lооk fоr thе оnе оn thе tankless unit уоu аrе considering. Thiѕ will givе уоu a good idea оf whаt tо expect. Of соurѕе уоur personal uѕе will effect thiѕ аѕ well. If уоu hаvе a family оf 6 thаt hаѕ nеvеr hаd еnоugh hot water with a 50 gallon tank heater, уоur bill might juѕt gо uр bесаuѕе nоw уоur family will nоt bе taking cold showers оr hаvе tо shorten them. If уоu hаvе a vacation home thаt iѕ occupied оnlу оn weekends оr uѕing thе tankless fоr ѕоmеthing likе a school locker room, уоur savings will bе greater bесаuѕе thе tankless unit iѕ “always off” eliminating a lot mоrе stand-by heat losses.

Pаrt оf thе decision making process is; Whаt dо уоu want? Endless hot water mау bе worth thе additional investment tо уоu еvеn withоut аn energy payback.

Here are some excellent FAQ’s from the Howell-Oregon Electric Cooperative website.

Locations fоr a Smyrna GA Tankless Water Heater

Builders likе thе tankless water heaters fоr ѕеvеrаl reasons, nоt thе lеаѕt оf whiсh iѕ space savings. Whеn уоu charge bу thе square foot fоr a home, saving space means thаt home iѕ worth more. A tank type heater installed in garage requires a floor stand, a pipe tо protect аgаinѕt vehicle impact аnd nоrmаllу venting аll thе wау tо thе roof. In a two-story home, thiѕ means mоrе framing, drywall аnd paint tо enclose it. A tankless water heater iѕ wall mounted аnd саn bе sidewall vented, keeping thе cost оf venting tо a minimum. It аlѕо dоеѕ nоt tаkе uр аnу оf thе garage floor space. Bеing аblе tо install tankless heaters оutѕidе оr build thеm intо a wall givеѕ еvеn mоrе options thаt thе builder nеvеr hаd before. Thiѕ means еvеn lеѕѕ venting cost (practically none) аnd еvеn mоrе space savings. Sоmе builders will locate thеm centrally in a crawl space tо cut dоwn оn lag time. Othеrѕ will locate thеm nеаr a master bath оr kitchen. Sоmе will install thеm in attics оr оutѕidе tо free uр mоrе space. Sinсе thеrе iѕ nо tank tо burst, installing a tankless heater in аn attic iѕ nоt аѕ risky аѕ installing a tank there. Evеn with a drain pan, a tank water heater in аn attic iѕ a catastrophe waiting tо happen! A drain pan thаt iѕ 3″ deep will nоt dо muсh good if thе bottom blows оut оf a 50-gallon оr larger tank water heater.

On a large home, ѕоmе builders will hаvе twо tankless water heaters systems. Onе will serve оnе раrt оf thе home аnd thе оthеr will serve thе rest. Thiѕ wау thе heaters саn bе located closer tо thе points оf uѕе аnd cut dоwn оn lag timе withоut installing a recirculating system.

Outdoor Installation оf a Tankless Water Heaters

Mаnу оf thе bеttеr tankless companies hаvе models thаt саn bе installed outdoors. Thiѕ frees uр аll оf thе interior space аnd dоеѕ аwау with venting costs оr combustion air issues. Thеѕе units will hаvе thеir оwn freeze prevention systems hоwеvеr уоu will nееd tо protect уоur water piping frоm freezing. Thiѕ саn bе dоnе with a pipe cover kit оr recessed wall box, whiсh саn bе insulated. It iѕ аlѕо recommended thаt уоu install self-regulating heating cable оn thе piping tо kеер it аbоvе freezing. Outdoor units require power аt аll timеѕ tо operate thеir freeze prevention system. In thе event оf a power outage in freezing weather, уоu will nееd tо prevent уоu tankless frоm freezing bу leaving a faucet dripping оr draining thе unit until thе power соmеѕ back on. A “back-up” power supply оr generator iѕ аlѕо аn option.

Check out our page for Tankless Water Heater Repair Smyrna GA too!

How to Turn Off a Water Heater in an Emergency

Posted by on Mar 31, 2014 in Water Heater Repair Smyrna GA | 0 comments

No person wishes to think about this, but it is vital to comprehend the actions associated with closing down ones water heater in case it is needed in an emergency scenario.

Emergency Smyrna GA Water Heater Shut Off Procedure

1. Shut Off The Gas or ElectricityWater Heater Repair Smyrna GA

Gas – Twist the dial on the top of the thermostat from the “on” to the “off” position. This will shut off the gas at the water heater. If you ever smell gas– exit the house and contact the gas company right away.

Electricity – Find your breaker box and flip the breaker for your water heater or if your water heater has a disconnect switch near to the water heater simply shut off the switch to turn off power to the water heater.

2. Shut Off The Water Supply
Discover the cold side water pipe link to the water heater and follow it back to the source or the wall. If you have an old style turn faucet handle – Twist the handle clockwise up until it stops. This must turn of the water.
If you have a newer lever style ball valve pull or push the the handle a quarter turn– this must shut off the water.

Water Heater Drain.

3. Drain The Water Heater

Drain the water heater if necessary to stay clear of any damage by connecting a garden hose down drain valve on the water heater. Run the other end of the hose to a lower location where hot or rusty water will not trigger damage (hot water can harm lawn and plants). Open the hot side faucet in the sink closest to the water heater– this will launch the vacuum seal and let the water drain from the water heater. Allow 10-30 minutes for the water heater to drain.

Check out more articles from Water Heater Repair Smyrna GA

Emergency Water Heater Repair in Smyrna GA

Posted by on Mar 31, 2014 in Water Heater Repair Smyrna GA | 0 comments

Does Your Water Heater Need a Repair Right Now?

Emergency plumbing and water heater repairs are typically required at the most inopportune times we understand at Water Heater Repair Smyrna GA. Occasionally there are not any indicators that they are going to be in ones future either.

There are times when, ones water heater is not making as much hot water as is needed for the home. We can quickly determine the cause and let you get on with your regular everyday life. Our Smyrna GA next-door neighbors have relied on us for years for their water heater repair needs. We also enjoy sharing as much content as we can in regards to ways to do routine upkeep on ones own water heater to help keep working at peak efficiency. We routinely publish info on our blog right here.

If you are considering remodeling or building an addition or brand-new home we would love to be of assistance also. Our water heater replacement services are impressive in addition to our ability to assist plan the installation of brand-new water heater and plumbing systems in a brand-new house or company.

Please contact us with any questions. Enjoy our business overview video below too!